Internet-Draft PCEP for Native IP September 2024
Wang, et al. Expires 15 March 2025 [Page]
Workgroup:
PCE Working Group
Internet-Draft:
draft-ietf-pce-pcep-extension-native-ip-40
Published:
Intended Status:
Experimental
Expires:
Authors:
A. Wang
China Telecom
B. Khasanov
MTS Web Services (MWS)
S. Fang
Huawei Technologies
R. Tan
Huawei Technologies
C. Zhu
ZTE Corporation

Path Computation Element Communication Protocol (PCEP) Extensions for Native IP Networks

Abstract

This document introduces extensions to the PCE Communication Protocol (PCEP) to support path computation in native IP networks through a PCE-based central control mechanism known as Centralized Control Dynamic Routing (CCDR). These extensions empower a PCE to calculate and manage paths specifically for native IP networks, expand PCEP’s capabilities beyond its traditional use in MPLS and GMPLS networks. By implementing these extensions, IP network resources can be utilized more efficiently, facilitating the deployment of traffic engineering in native IP environments.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 15 March 2025.

Table of Contents

1. Introduction

Generally, Multiprotocol Label Switching Traffic Engineering (MPLS-TE) requires the corresponding network devices to support Resource ReSerVation Protocol (RSVP)[RFC3209]/Label Distribution Protocol (LDP)[RFC5036] protocols to ensure the End-to-End (E2E) traffic performance. But in native IP network scenarios described in [RFC8735], there will be no such signaling protocol to synchronize the actions among different network devices. It is feasible to use the central control mode described in [RFC8283] to correlate the forwarding behavior among different network devices. [RFC8821] describes the architecture and solution philosophy for the E2E traffic assurance in the Native IP network via multiple Border Gateway Protocol (BGP) sessions-based solution. It requires only the PCE to send the instructions to the PCCs, to build multiple BGP sessions, distribute different prefixes on the established BGP sessions and assign the different paths to the BGP next hops.

This document describes the corresponding Path Computation Element Communication Protocol (PCEP) extensions to transfer the key information about BGP peer, peer prefix advertisement, and the explicit peer route on on-path routers.

2. Conventions used in this document

The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

2.1. Use of RBNF

The message formats in this document are illustrated using Routing Backus-Naur Form (RBNF) encoding, as specified in [RFC5511]. The use of RBNF is illustrative only and may elide certain important details; the normative specification of messages is found in the prose description. If there is any divergence between the RBNF and the prose, the prose is considered authoritative.

2.2. Experimental Status Consideration

The procedures outlined in this document are experimental. The experiment aims to explore the use of PCE (and PCEP) for end-to-end traffic assurance in Native IP networks through multiple BGP sessions. Additional implementation is necessary to gain a deeper understanding of the operational impact, scalability, and stability of the mechanism described. Feedback from deployments will be crucial in determining whether this specification should advance from Experimental to the IETF Standards Track.

3. Terminology

This document uses the following terms defined in [RFC5440]: PCC, PCE, PCEP.

The following terminology is used in this document:

4. Capability Advertisement

4.1. Open Message

During the PCEP Initialization Phase, PCEP Speakers (PCE or PCC) advertise their support of Native IP extensions.

This document defines a new Path Setup Type (PST) [RFC8408] for Native-IP, as follows:

A PCEP speaker MUST indicate its support of the function described in this document by sending a PATH-SETUP-TYPE-CAPABILITY TLV in the OPEN object with this new PST included in the PST list.

[RFC9050] defined the PCECC-CAPABILITY sub-TLV to exchange information about their PCECC capability. A new flag is defined in PCECC-CAPABILITY sub-TLV for Native IP:

N (NATIVE-IP-TE-CAPABILITY - 1 bit - 30): When set to 1 by a PCEP speaker, this flag indicates that the PCEP speaker is capable of TE in a Native IP network, as specified in this document. Both the PCC and PCE MUST set this flag to support this extension.

If a PCEP speaker receives the PATH-SETUP-TYPE-CAPABILITY TLV with the newly defined path setup type, but without the N bit set in PCECC-CAPABILITY sub-TLV, it MUST:

If a PCEP speaker receives the PATH-SETUP-TYPE-CAPABILITY TLV with the newly defined path setup type, but without the PCECC-CAPABILITY sub-TLV, it MUST:

If one or both speakers (PCE and PCC) have not indicated the support for Native-IP, the PCEP extensions for the Native-IP MUST NOT be used. If a Native-IP operation is attempted when both speakers have not agreed on the OPEN messages, the receiver of the message MUST:

5. PCEP Messages

PCECC Native IP TE solution uses the existing PCE Label Switched Path (LSP) Initiate Request message (PCInitiate) [RFC8281], and PCE Report message (PCRpt) [RFC8231] to accomplish the multiple BGP sessions establishment, E2E Native-IP TE path deployment, and route prefixes advertisement among different BGP sessions. A new PST for Native-IP is used to indicate the path setup based on TE in Native IP networks.

The extended PCInitiate message described in [RFC9050] is used to download or remove the central controller's instructions (CCIs). [RFC9050] specifies an object called CCI for the encoding of the central controller's instructions. This document specifies a new CCI Object-Type for Native IP. The PCEP messages are extended in this document to handle the PCECC operations for Native IP. Three new PCEP Objects (BGP Peer Info (BPI) Object, Explicit Peer Route (EPR) Object, and Peer Prefix Advertisement (PPA) Object) are defined in this document. Refer to Section 7 for detailed object definitions. All PCEP procedures specified in [RFC9050] continue to apply unless specified otherwise.

5.1. The PCInitiate Message

The PCInitiate Message defined in [RFC8281] and extended in [RFC9050] is further extended to support Native-IP CCI.

The format of the extended PCInitiate message is as follows:

     <PCInitiate Message> ::= <Common Header>
                              <PCE-initiated-lsp-list>
  Where:
     <Common Header> is defined in [RFC5440]

     <PCE-initiated-lsp-list> ::= <PCE-initiated-lsp-request>
                                  [<PCE-initiated-lsp-list>]

     <PCE-initiated-lsp-request> ::=
                          (<PCE-initiated-lsp-instantiation>|
                           <PCE-initiated-lsp-deletion>|
                           <PCE-initiated-lsp-central-control>)

     <PCE-initiated-lsp-central-control> ::= <SRP>
                                             <LSP>
                                             <cci-list>

     <cci-list> ::=  <CCI>
                     [<BPI>|<EPR>|<PPA>]
                     [<cci-list>]

Where:

  • <PCE-initiated-lsp-instantiation> and <PCE-initiated-lsp-deletion> are as per [RFC8281].

  • The LSP and SRP objects are defined in [RFC8231].

When the PCInitiate message is used for Native IP instructions, i.e. When the CCI Object-Type is 2, the SRP, LSP and CCI objects MUST be present. Error handling for missing SRP, LSP or CCI objects MUST be performed as specified in [RFC9050]. Additionally, exactly one object among the BPI, EPR, or PPA objects MUST be present. The PLSP-ID and Symbolic Path Name TLVs are set as per the existing rules in [RFC8231], [RFC8281], and [RFC9050]. The Symbolic Path Name is used by the PCE/PCC to uniquely identify the E2E native IP TE path. The related Native-IP instructions with BPI, EPR or PPA objects are identified by the same Symbolic Path Name.

If none of the BPI, EPR or PPA objects are present, the receiving PCC MUST send a PCErr message with Error-type=6 (Mandatory Object missing) and Error-value=19 (Native IP object missing). If there is more than one instance of BPI, EPR or PPA object present, the receiving PCC MUST send a PCErr message with Error-type=19 (Invalid Operation) and Error-value=22 (Only one BPI, EPR or PPA object can be included in this message).

When the PCInitiate message is not used for Native IP instructions, i.e. When CCI Object-Type is not equal to 2, the BPI, EPR and PPA objects SHOULD NOT be present. If present, they MUST be ignored by the receiver.

To clean up the existing Native IP instructions, the SRP object MUST set the R (remove) bit.

5.2. The PCRpt Message

The PCRpt message is used to acknowledge the Native-IP instructions received from the central controller (PCE) as well as during the State Synchronization phase.

The format of the PCRpt message is as follows:

      <PCRpt Message> ::= <Common Header>
                          <state-report-list>
   Where:

      <state-report-list> ::= <state-report>[<state-report-list>]

      <state-report> ::= (<lsp-state-report>|
                          <central-control-report>)

      <lsp-state-report> ::= [<SRP>]
                             <LSP>
                             <path>

      <central-control-report> ::= [<SRP>]
                                   <LSP>
                                   <cci-list>

      <cci-list> ::=  <CCI>
                     [<BPI>|<EPR>|<PPA>]
                     [<cci-list>]
  • Where: <path> is as per [RFC8231] and the LSP and SRP objects are also defined in [RFC8231].

The error handling for missing CCI objects is as per [RFC9050]. Furthermore, one, and only one, object among BPI, EPR or PPA object MUST be present.

If none of the BPI, EPR or PPA objects are present, the receiving PCE MUST send a PCErr message with Error-type=6 (Mandatory Object missing) and Error-value=19 (Native IP object missing). If there are more than one instance of BPI, EPR or PPA objects present, the receiving PCE MUST send a PCErr message with Error-type=19 (Invalid Operation) and Error-value=22 (Only one BPI, EPR or PPA object can be included in this message).

When the PCInitiate message is not used for Native IP instructions, i.e. When CCI Object-Type is not equal to 2, the BPI, EPR and PPA objects SHOULD NOT be present. If present, they MUST be ignored by the receiver.

6. PCECC Native IP TE Procedures

The detailed procedures for the TE in the native IP environment are described in the following sections.

6.1. BGP Session Establishment Procedures

The PCInitiate and PCRpt message pair is used to exchange the configuration parameters for a BGP peer session. This pair of PCEP messages are exchanged between a PCE and each BGP peer (acting as PCC) which needs to establish a BGP session. After the BGP peer session has been initiated via this pair of PCEP messages, the BGP session establishes and operates in a normal fashion. The BGP peers can be used for External BGP (EBGP) peers or Internal BGP (IBGP) peers. For IBGP connection topologies, the Route Reflector (RR) is required.

The PCInitiate message is sent to the BGP router and/or RR (which are acting as PCC).

The RR topology for a single Autonomous System (AS) is shown in Figure 1. The BGP routers R1, R3, and R7 are within a single AS. R1 and R7 are BGP RR clients, and R3 is a RR. The PCInitiate message is sent to the BGP routers R1, R3 and R7 that need to establish a BGP session.

PCInitiate message creates an auto-configuration function for these BGP peers by providing the indicated Peer AS and the Local/Peer IP Address.

When the PCC receives the BPI and CCI object (with the R bit set to 0 in the SRP object) in the PCInitiate message, the PCC SHOULD try to establish the BGP session with the indicated Peer as per AS and Local/Peer IP address.

During the establishment procedure, the PCC MUST report to the PCE the status of the BGP session via the PCRpt message, with the status field in the BPI object set to the appropriate value and the corresponding SRP and CCI objects included.

When the PCC receives this message with the R bit set to 1 in the SRP object in the PCInitiate message, the PCC MUST clear the BGP configuration and tear down the BGP session that is indicated by the BPI object.

When the PCC clears successfully the specified BGP session configuration, it MUST report the result via the PCRpt message, with the BPI object included, and the corresponding SRP and CCI objects.

                             +------------------+
                 +----------->       PCE        <----------+
                 |           +--------^---------+          |
                 |                    |                    |
                 |             PCInitiate/PCRpt            |
                 |                    |                    |
                 |               +----v--+                 |
                 +---------------+ R3(RR)+-----------------+
                 |               +-------+                 |
           PCInitiate/PCRpt                         PCInitiate/PCRpt
                 |                                         |
                +v-+          +--+          +--+         +-v+
                |R1+----------+R5+----------+R6+---------+R7|
                ++-+          +-++          +--+         +-++
                 |              |                          |
                 |            +--+          +--+           |
                 +------------+R2+----------+R4+-----------+
                              +--+          +--+
       Figure 1: BGP Session Establishment Procedures(R3 act as RR)

The message peers, message type, message key parameters and procedures in the above figures are shown below:

              +-------+                                       +-------+
              |PCC    |                                       |  PCE  |
              |R1     |                                       +-------+
       +------|       |                                            |
       | PCC  +-------+                                            |
       | R3     | |   (For R1/R3 BGP Session on R1)                |
+------|        | |<-PCInitiate,CC-ID=X,Symbolic Path Name=Class A-|
|      |        | |BPI Object(Peer AS, Local_IP=R1_A, Peer_IP=R3_A)|
|PCC   +--------+ |                                                |
|R7      |  |     |----PCRpt,CC-ID=X(Symbolic Path Name=Class A)-->|
|        |  |     |BPI Object(Peer AS, Local_IP=R1_A, Peer_IP=R3_A)|
+--------+  |                                                      |
    |       |          (For R1/R3 BGP Session on R3)               |
    |       |<--PCInitiate,CC-ID=Y1,Symbolic Path Name=Class A-----|
    |       |      BPI Object(Peer AS, Local_IP=R3_A, Peer_IP=R1_A)|
    |       |---PCRpt,CC-ID=Y1,Symbolic Path Name=Class A--------->|
    |       |      BPI Object(Peer AS, Local_IP=R3_A, Peer_IP=R1_A)|
    |       |                                                      |
    |       |          (For R3/R7 BGP Session on R3)               |
    |       |<--PCInitiate,CC-ID=Y2,Symbolic Path Name=Class A-----|
    |       |  BPI Object(Peer AS, Local_IP=R3_A, Peer_IP=R7_A)    |
    |       |----PCRpt,CC-ID=Y2,Symbolic Path Name=Class A-------->|
    |       |  BPI Object(Peer AS, Local_IP=R3_A, Peer_IP=R7_A)    |
    |                                                              |
    |                  (For R3/R7 BGP Session on R7)               |
    |<--PCInitiate,CC-ID=Z,Symbolic Path Name=Class A--------------|
    |            BPI Object(Peer AS, Local_IP=R7_A, Peer_IP=R3_A)  |
    |---PCRpt,CC-ID=Z,Symbolic Path Name=Class A------------------>|
    |            BPI Object(Peer AS, Local_IP=R7_A, Peer_IP=R3_A)  |

               Figure 2: Message Information and Procedures

The Local/Peer IP address MUST be dedicated to the usage of the native IP TE solution, and MUST NOT be used by other BGP sessions that are established manually or in other ways. If the Local IP Address or Peer IP Address within the BPI object is used in other existing BGP sessions, the PCC MUST report such an error situation via a PCErr message with:

  • Error-type=33 (Native IP TE failure) and Error-value=1 (Local IP is in use), or

  • Error-type=33 (Native IP TE failure )and Error-value=2 (Remote IP is in use).

  • The detailed Error-Types and Error-Values are defined in Section 8

If the established BGP session is broken, the PCC MUST report such information via PCRpt message with the status field set to "BGP session down" in the associated BPI Object. The error code field within the BPI object SHOULD indicate the reason that leads to the BGP session being down. In the future, when the BGP session is up again, the PCC MUST report that as well via the PCRpt message with the status field set to "BGP Session Established".

6.2. Explicit Route Establishment Procedures

The explicit route establishment procedures can be used by PCE to install a route on the PCC, using the PCInitiate and PCRpt message pair. Such explicit routes operate the same as static routes installed by network management protocols (Network Configuration Protocol (NETCONF)/YANG). The procedures of such explicit route addition and removal MUST be controlled by the PCE in a specific order so that the pathways are established without loops.

For the purpose of explicit route addition, the PCInitiate message ought to be sent to every router on the explicit path. In the example, for the explicit route from R1 to R7, the PCInitiate message is sent to R1, R2 and R4, as shown in Figure 3. For the explicit route from R7 to R1, the PCInitiate message is sent to R7, R4 and R2, as shown in Figure 5.

When the PCC receives the EPR and the CCI object (with the R bit set to 0 in the SRP object) in the PCInitiate message, the PCC SHOULD install the explicit route to the peer in the RIB/FIB.

When the PCC installs successfully the explicit route to the peer, it MUST report the result via the PCRpt messages, with the EPR object and the corresponding SRP and CCI objects included.

When the PCC receives the EPR and the CCI object with the R bit set to 1 in the SRP object in the PCInitiate message, the PCC MUST remove the explicit route to the peer that is indicated by the EPR object.

When the PCC has removed the explicit route that is indicated by this object, it MUST report the result via the PCRpt message, with the EPR object included, and the corresponding SRP and CCI object.

                          +------------------+
               +---------->       PCE        +
               |          +----^-----------^-+
               |               |           |
               |               |           |
               |               | +------+  |
               +---------------|-+R3(RR)+--|-------------+
          PCInitiate/PCRpt     | +------+  |             |
               |               |           |             |
              +v-+      +--+   |           |   +--+    +--+
              |R1+------+R5+---+-----------|---+R6+----+R7|
              ++-+      +--+   |           |   +--+    +-++
               |     PCInitiate/PCRpt  PCInitiate/PCRpt  |
               |               |           |             |
               |            +--v--+     +--v-+           |
               +------------+- R2 +-----+ R4 +-----------+
                            +--+--+     +--+-+
    Figure 3: Explicit Route Establish Procedures(From R1 to R7)

The message peers, message type, message key parameters and procedures in the above figures are shown below:

              +-------+                                       +-------+
              |PCC    |                                       |  PCE  |
              |R4     |                                       +-------+
       +------|       |                                           |
       | PCC  +-------+                                           |
       | R2     | |        (EPR route on R4)                      |
+------|        | |<-PCInitiate,CC-ID=Z,Symbolic Path Name=Class A|
|      |        | |   EPR Object(Peer Address=R7_A, Next Hop=R7_A)|
|PCC   +--------+ |                                               |
|R1      |  |     |----PCRpt,CC-ID=Z,Symbolic Path Name=Class A-->|
|        |  |     |   EPR Object(Peer Address=R7_A, Next Hop=R7_A)|
+--------+  |                                                     |
    |       |              (EPR route on R2)                      |
    |       |<--PCInitiate,CC-ID=Y,Symbolic Path Name=Class A-----|
    |       |   EPR Object(Peer Address=R7_A, Next Hop=R4_A)      |
    |       |----PCRpt,CC-ID=Y,Symbolic Path Name=Class A-------->|
    |       |   EPR Object(Peer Address=R7_A, Next Hop=R4_A)      |
    |       |                                                     |
    |                                                             |
    |                      (EPR route on R1)                      |
    |<--PCInitiate,CC-ID=X,Symbolic Path Name=Class A-------------|
    |              EPR Object(Peer Address=R7_A, Next Hop=R2_A)   |
    |---PCRpt,CC-ID=X1(Symbolic Path Name=Class A)--------------->|
    |              EPR Object(Peer Address=R7_A, Next Hop=R2_A)   |

           Figure 4: Message Information and Procedures
                    +------------------+
                    +       PCE        <-----------+
                    +----^-----------^-+           |
                         |           |             |
                         |           |             |
                         | +------+  |             |
         +-----------------+R3(RR)+--|-------------+
         |               | +------+  |       PCInitiate/PCRpt
         |               |           |             |
        +--+      +--+   |           |   +--+    +-v+
        |R1+------+R5+---+-----------|---+R6+----+R7|
        ++-+      +--+   |           |   +--+    +-++
         |       PCInitiate/PCRpt PCInitiate/PCRpt |
         |               |           |             |
         |            +--v--+     +--v-+           |
         +------------+- R2 +-----+ R4 +-----------+
                      +--+--+     +--+-+
    Figure 5: Explicit Route Establish Procedures(From R7 to R1)

The message peers, message type, message key parameters and procedures in the above figures are shown below:

              +-------+                                       +-------+
              |PCC    |                                       |  PCE  |
              |R2     |                                       +-------+
       +------|       |                                           |
       | PCC  +-------+                                           |
       | R4     | |        (EPR route on R2)                      |
+------|        | |<-PCInitiate,CC-ID=X,Symbolic Path Name=Class A|
|      |        | |  EPR Object(Peer Address=R1_A, Next Hop=R1_A) |
|PCC   +--------+ |                                               |
|R7      |  |     |----PCRpt,CC-ID=X,Symbolic Path Name=Class A-->|
|        |  |     |  EPR Object(Peer Address=R1_A, Next Hop=R1_A) |
+--------+  |                                                     |
    |       |              (EPR route on R4)                      |
    |       |<--PCInitiate,CC-ID=Y,Symbolic Path Name=Class A-----|
    |       |   EPR Object(Peer Address=R1_A, Next Hop=R2_A)      |
    |       |----PCRpt,CC-ID=Y,Symbolic Path Name=Class A-------->|
    |       |   EPR Object(Peer Address=R1_A, Next Hop=R2_A)      |
    |       |                                                     |
    |                                                             |
    |                      (EPR route on R7)                      |
    |<--PCInitiate,CC-ID=Z,Symbolic Path Name=Class A-------------|
    |   EPR Object(Peer Address=R1_A, Next Hop=R4_A)              |
    |---PCRpt,CC-ID=Z,Symbolic Path Name=Class A----------------->|
    |   EPR Object(Peer Address=R1_A, Next Hop=R4_A)              |

    Figure 6: Explicit Route Establish Procedures(From R7 to R1)

To avoid the transient loop while deploying the explicit peer route, the EPR object MUST be sent to the PCCs in the reverse order of the E2E path. To remove the explicit peer route, the EPR object MUST be sent to the PCCs in the same order as the E2E path.

To accomplish ECMP effects, the PCE can send multiple EPR/CCI objects to the same node, with the same route priority and peer address value but a different next-hop address.

The PCC MUST verify that the next hop address is reachable. In case of failure, the PCC MUST send the corresponding error via PCErr message, with the error information: Error-type=33 (Native IP TE failure), Error-value=3 (Explicit Peer Route Error).

When the peer info is not the same as the peer info that is indicated in the BPI object in PCC for the same path that is identified by Symbolic Path Name TLV, a PCErr message MUST be reported, with the error information: Error-type=33 (Native IP TE failure), Error-value=4, EPR/BPI Peer Info Mismatch. Note that the same error can be used in case no BPI is received at the PCC.

If the PCE needs to update the path, it MUST first instruct the new CCI with updated EPR corresponding to the new next hop to use and then instruct the removal of the older CCI.

6.3. BGP Prefix Advertisement Procedures

The detailed procedures for BGP prefix advertisement are shown below, using the PCInitiate and PCRpt message pair.

The PCInitiate message SHOULD be sent to PCC that acts as a BGP peer edge router only. In the example, it is sent to R1 and R7 respectively.

When the PCC receives the PPA and the CCI object (with the R bit set to 0 in the SRP object) in the PCInitiate message, the PCC SHOULD send the prefixes indicated in this object to the identified BGP peer via the corresponding BGP session [RFC4271].

When the PCC has successfully sent the prefixes to the appointed BGP peer, it MUST report the result via the PCRpt messages, with the PPA object and the corresponding SRP and CCI objects included.

When the PCC receives the PPA and the CCI object with the R bit set to 1 in the SRP object in the PCInitiate message, the PCC MUST withdraw the prefixes advertisement to the peer indicated by this object.

When the PCC withdraws successfully the prefixes that are indicated by this object, it MUST report the result via the PCRpt message, with the PPA object included, and the corresponding SRP and CCI objects.

                 +------------------+
      +---------->       PCE        <-----------+
      |          +------------------+           |
      |                  +--+                   |
      +------------------+R3+-------------------+
PCInitiate/PCRpt         +--+             PCInitiate/PCRpt
      |                                         |
     +v-+          +--+          +--+         +-v+
     |R1+----------+R5+----------+R6+---------+R7|
     ++-+          +--+          +--+         +-++
 (BGP Router)                           (BGP Router)
      |                                         |
      |                                         |
      |            +--+          +--+           |
      +------------+R2+----------+R4+-----------+
                   +--+          +--+
   Figure 7: BGP Prefix Advertisement Procedures

The message peers, message type, message key parameters and procedures in the above figures are shown below:

              +-------+                                      +-------+
              |PCC    |                                      |  PCE  |
              |R1     |                                      +-------+
       +------|       |                                           |
       | PCC  +-------+                                           |
       | R7     | |   (Instruct R1 to advertise Prefix 1_A to R7) |
       |        | |<-PCInitiate,CC-ID=X,Symbolic Path Name=Class A|
       |        | |  PPA Object(Peer IP=R7_A, Prefix=1_A)         |
       +--------+ |                                               |
            |     |----PCRpt,CC-ID=X,Symbolic Path Name=Class A-->|
            |     |    PPA Object(Peer IP=R7_A, Prefix=1_A)       |
            |                                                     |
            |     (Instruct R7 to advertise Prefix 7_A to R1 )    |
            |<--PCInitiate,CC-ID=Z,Symbolic Path Name=Class A-----|
            |         PPA Object(Peer IP=R1_A, Prefix=7_A)        |
            |----PCRpt,CC-ID=Z,Symbolic Path Name=Class A-------->|
            |              PPA Object(Peer IP=R1_A, Prefix=7_A)   |
            |                                                     |

            Figure 8: Message Information and Procedures

The AFI/SAFI for the corresponding BGP session SHOULD match the Peer Prefix Advertisement Object-Type, AFI/SAFI SHOULD be 1/1 for the IPv4 prefix and 2/1 for the IPv6 prefix. In case of mismatch, an error: Error-type=33 (Native IP TE failure), Error-value=5 (BPI/PPA address family mismatch) MUST be reported via PCErr message.

When the peer info is not the same as the peer info that is indicated in the BPI object in PCC for the same path that is identified by Symbolic Path Name TLV, an error: Error-type=33 (Native IP TE failure), Error-value=6 (PPA/BPI peer info mismatch) MUST be reported via the PCErr message. Note that the same error can be used in case no BPI is received at the PCC.

6.4. Selection of Raw Mode and Tunnel Mode Forwarding Strategy

Normally, when the above procedures are finished, the user traffic will be forwarded via the appointed path, but the forwarding will be based solely on the destination of user traffic. If there is traffic from different attached points to the same destination coming into the network, they could share the priority path which may not be the initial desire. For example, as illustrated in Figure 1, the initial aim is to ensure traffic that enters the network via R1 and exits the network at R7 via R5-R6-R7. If some traffic enters the network via the R2 router, passes through R5 and exits at R7, they may share the priority path among R5-R6-R7, which may not be the desired effect.

The above normal traffic forwarding behavior is clarified as a Raw mode forwarding strategy. Such a mode can achieve only the moderate traffic path control effect. To achieve the strict traffic path control effect, the entry point MUST tunnel the user traffic from the entry point of the network to the exit point of the network, which is also between the BGP peer established via Section 6.1. Such forwarding behavior is called the Tunnel mode forwarding strategy. For simplicity, the IPinIP tunnel type [RFC2003] is used between the BGP peers by default.

The selection of Raw mode and Tunnel mode forwarding strategies are controlled via the "T" bit in BPI Object that is defined in Section 7.2

6.5. Clean Up

To remove the Native-IP state from the PCC, the PCE MUST send explicit CCI cleanup instructions for PPA, EPR and BPI objects respectively with the R flag set in the SRP object. If the PCC receives a PCInitiate message but does not recognize the Native-IP information in the CCI, the PCC MUST generate a PCErr message with Error-Type=19 (Invalid operation) and Error-value=30 (Unknown Native-IP Info) and MUST include the SRP object to specify the error is for the corresponding cleanup (via a PCInitiate message).

6.6. Other Procedures

The handling of the state synchronization, redundant PCEs, re-delegation and clean up is the same as other CCIs as specified in [RFC9050].

7. New PCEP Objects

One new CCI Object type and three new PCEP objects are defined in this document. All new PCEP objects are as per [RFC5440].

7.1. CCI Object

The Central Control Instructions (CCI) Object (defined in [RFC9050]) is used by the PCE to specify the forwarding instructions. This document defines another object type for Native-IP procedures.

CCI Object-Type is 2 for Native-IP as below:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                            CC-ID                              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|          Reserved             |             Flags             |
+---------------------------------------------------------------+
|                                                               |
//                        Optional TLVs                        //
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 9: CCI Object for Native IP

The field CC-ID is as described in [RFC9050]. The following fields are defined for CCI Object-Type 2

Reserved:
2 bytes, is set to zero while sending and ignored on receipt.
Flags:
2 bytes, is used to carry any additional information about the Native-IP CCI. Currently, no flag bits are defined. Unassigned flags are set to zero while sending and ignored on receipt.

Optional TLVs may be included within the CCI object body. The Symbolic Path Name TLV [RFC8231] MUST be included in the CCI Object-Type 2 to identify the E2E TE path in the Native IP environment.

7.2. BGP Peer Info Object

The BGP Peer Info object is used to specify the information about the peer with which the PCC want to establish the BGP session. This object is included and sent to the source and destination router of the E2E path in case there is no Route Reflection (RR) involved. If the RR is used between the source and destination routers, then such information is sent to the source router, RR and destination router respectively.

By default, the Local/Peer IP address MUST be a unicast address and dedicated to the usage of the native IP TE solution, and MUST NOT be used by other BGP sessions that are established by manual or other configuration mechanisms.

BGP Peer Info Object-Class is 46

BGP Peer Info Object-Type is 1 for IPv4 and 2 for IPv6

The format of the BGP Peer Info object body for IPv4 (Object-Type=1) is as follows:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                      Peer AS Number                           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|   ETTL        |     Status    |   Error Code  |    Flag     |T|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                    Local IP Address                           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                    Peer IP Address                            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
//                    Optional TLVs                            //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     Figure 10: BGP Peer Info Object Body Format for IPv4

The format of the BGP Peer Info object body for IPv6 (Object-Type=2) is as follows:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                      Peer AS Number                           |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|   ETTL        |      Status   |   Error Code  |    Flag     |T|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|               Local IP Address (16 bytes)                     |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|               Peer IP Address (16 bytes)                      |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
//                    Optional TLVs                            //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      Figure 11: BGP Peer Info Object Body Format for IPv6
  • Peer AS Number: 4 bytes, to indicate the AS number of Remote Peer. Note that if 2-byte AS numbers are in use, the low-order bits (16 through 31) is used, and the high-order bits (0 through 15) is set to zero.

  • ETTL: 1 byte, EBGP Time To Live, to indicate the multi-hop count for the EBGP session. It should be 0 and ignored when Local AS and Peer AS are the same.

  • Status: 1 byte, Indicate BGP session status between the peers. Its values are defined below:

    • 0: Reserved

    • 1: BGP Session Established

    • 2: BGP Session Establishment In Progress

    • 3: BGP Session Down

    • 4-255: Reserved

  • Error Code: 1 byte, Indicate the reason that the BGP session can't be established.

    • 0: Unspecific

    • 1: ASes do not match, BGP Session Failure

    • 2: Peer IP can't be reached, BGP Session Failure

    • 3-255: Reserved

  • Flag: 1 byte.

    • Currently, only bit 7 (T bit) is defined. When the T bit is set, the traffic SHOULD be sent in the IPinIP tunnel (Tunnel source is Local IP Address, tunnel destination is Peer IP Address). When the T bit is cleared, the traffic is sent via its original source and destination address. The Tunnel mode(T bit is set) is used when the operator wants to ensure only the traffic from the specified (entry, exit) pair, and the Raw mode (T bit is clear) is used when the operator wants to ensure traffic from any entry to the specified destination. Unassigned flags are set to zero while sending and ignored on receipt.

  • Local IP Address(4/16 bytes): Unicast IP address of the local router, used to peer with another end router. When Object-Type is 1, the length is 4 bytes; when Object-Type is 2, the length is 16 bytes.

  • Peer IP Address(4/16 bytes): Unicast IP address of the peer router, used to peer with the local router. When Object-Type is 1, the length is 4 bytes; when Object-Type is 2, the length is 16 bytes;

  • Optional TLVs: TLVs that are associated with this object, can be used to convey other necessary information for dynamic BGP session establishment. No TLVs are currently defined.

When the PCC receives a BPI object, with Object-Type=1, it SHOULD try to establish a BGP session with the peer in AFI/SAFI=1/1.

When the PCC receives a BPI object with Object-Type=2, it SHOULD try to establish a BGP session with the peer in AFI/SAFI=2/1.

7.3. Explicit Peer Route Object

The Explicit Peer Route object is defined to specify the explicit peer route to the corresponding peer address on each device that is on the E2E Native-IP TE path. This Object ought to be sent to all the devices on the path that is calculated by the PCE. Although the object is named as “Explicit Peer Route”, it can be seen that the routes it installs are simply host routes. The use of this object to install host routes for any purpose other than reaching the corresponding peer address on each device that is on the E2E Native-IP TE path is outside the scope of this specification.

By default, the path established by this object MUST have higher priority than the other paths calculated by dynamic IGP protocol, and MUST have lower priority than the static route configured by manual or NETCONF or any other static means.

Explicit Peer Route Object-Class is 47.

Explicit Peer Route Object-Type is 1 for IPv4 and 2 for IPv6

The format of the Explicit Peer Route object body for IPv4 (Object-Type=1) is as follows:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|       Route Priority        |          Reserved               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                       Peer IPv4 Address                       |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|               Next Hop IPv4 Address to the Peer               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
//                    Optional TLVs                            //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    Figure 12: Explicit Peer Route Object Body Format for IPv4

The format of the Explicit Peer Route object body for IPv6 (Object-Type=2) is as follows:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|       Route Priority        |           Reserved              |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                       Peer IPv6 Address                       |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                Next Hop IPv6 Address to the Peer              |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
//                    Optional TLVs                            //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    Figure 13: Explicit Peer Route Object Body Format for IPv6
  • Route Priority: 2 bytes; the priority of this explicit route. The higher priority SHOULD be preferred by the device. This field is used to indicate the preferred path at each hop.

  • Reserved: is set to zero while sending, ignored on receipt.

  • Peer (IPv4/IPv6) Address: Peer Address for the BGP session (4/16 bytes).

  • Next Hop (IPv4/IPv6) Address to the Peer: To indicate the next hop address (4/16 bytes) to the corresponding peer address.

  • Optional TLVs: TLVs that are associated with this object, can be used to convey other necessary information for explicit peer path establishment. No TLVs are currently defined.

7.4. Peer Prefix Advertisement Object

The Peer Prefix Advertisement object is defined to specify the IP prefixes that are advertised to the corresponding peer. This object needs only be included and sent to the source/destination router of the E2E path.

The prefix information included in this object MUST only be advertised to the indicated peer, and SHOULD NOT be advertised to other BGP peers.

Peer Prefix Advertisement Object-Class is 48

Peer Prefix Advertisement Object-Type is 1 for IPv4 and 2 for IPv6

The format of the Peer Prefix Advertisement object body is as follows:

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                  Peer IPv4 Address                            |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| No. of Prefix |                  Reserved                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                  IPv4 Prefix #1                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Prefix #1 Len  |                  Reserved                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                               :                               |
|                               :                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                  IPv4 Prefix #n                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Prefix #n Len  |                  Reserved                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
//                    Optional TLVs                            //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 14: Peer Prefix Advertisement Object Body Format for IPv4
 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                                                               |
|                  Peer IPv6 Address                            |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| No. of Prefix |                  Reserved                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                  IPv6 Prefix #1                               |
|                                                               |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Prefix #1 Len  |                  Reserved                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                               :                               |
|                               :                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|                  IPv6 Prefix #n                               |
|                                                               |
|                                                               |
|                                                               |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Prefix #n Len  |                  Reserved                     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
//                    Optional TLVs                            //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
 Figure 15: Peer Prefix Advertisement Object Body Format for IPv6
  • Common Fields:

    • No. of Prefix: 1 byte. Identifies the number of prefixes that are advertised to the peer in the PPA object.

    • Reserved: 3 bytes. Ought to be set to zero while sending and be ignored on receipt.

    • Prefix Len: 1 byte. Identifies the length of the prefix.

    • Optional TLVs: TLVs that are associated with this object, can be used to convey other necessary information for prefix advertisement. No TLVs are currently defined.

  • For IPv4:

    • Peer IPv4 Address: 4 bytes. Identifies the peer IPv4 address that the associated prefixes will be sent to.

    • IPv4 Prefix: 4 bytes. Identifies the prefix that will be sent to the peer identified by Peer IPv4 Address.

  • For IPv6:

    • Peer IPv6 Address: 16 bytes. Identifies the peer IPv6 address that the associated prefixes will be sent to.

    • IPv6 Prefix: Identifies the prefix that will be sent to the peer identified by Peer IPv6 Address.

    If in the future, a requirement is identified to advertise IPv4 prefixes toward an IPv6 peering address, or IPv6 prefixes towards an IPv4 peering address, then a new Peer Prefix Advertisement Object-Types can be defined for these purposes.

8. New Error-Types and Error-Values Defined

A PCEP-ERROR object is used to report a PCEP error and is characterized by an Error-Type that specifies that type of error and an Error-value that provides additional information about the error. An additional Error-Type and several Error-values are defined to represent the errors related to the newly defined objects that are related to Native IP TE procedures.

       +============+==========+=====================================+
       | Error-Type | Meaning  | Error-value                         |
       +=======+===============+=====================================+
       | 33    | Native IP TE failure                                |
       |       |                                                     |
       +-------+---------------+-------------------------------------+
       |       |               |0:Unassigned                         |
       +-------+---------------+-------------------------------------+
       |       |               |1:Local IP is in use                 |
       +-------+---------------+-------------------------------------+
       |       |               |2:Remote IP is in use                |
       +-------+---------------+-------------------------------------+
       |       |               |3:Explicit Peer Route Error          |
       +-------+---------------+-------------------------------------+
       |       |               |4:EPR/BPI Peer Info mismatch         |
       +-------+---------------+-------------------------------------+
       |       |               |5:BPI/PPA Address Family mismatch    |
       +-------+---------------+-------------------------------------+
       |       |               |6:PPA/BPI Peer Info mismatch         |
       +-------+---------------+-------------------------------------+
       | 6     | Mandatory Object missing                            |
       |       |                                                     |
       +-------+---------------+-------------------------------------+
       |       |               |19:Native IP object missing          |
       +-------+---------------+-------------------------------------+
       | 10    | Reception of an invalid object                      |
       |       |                                                     |
       +-------+---------------+-------------------------------------+
       |       |               |39:PCECC NATIVE-IP-TE-CAPABILITY bit |
       |       |               |is not set                           |
       +-------+---------------+-------------------------------------+
       | 19    | Invalid Operation                                   |
       |       |                                                     |
       +-------+---------------+-------------------------------------+
       |       |               |22:Only one BPI, EPR or PPA object   |
       |       |               |can be included in this message      |
       +-------+---------------+-------------------------------------+
       |       |               |29:Attempted Native-IP operations  |
       |       |               |when the capability was not          |
       |       |               | advertised                          |
       +-------+---------------+-------------------------------------+
       |       |               |30:Unknown Native-IP Info          |
       +-------+---------------+-------------------------------------+
            Figure 16: Newly defined Error-Type and Error-Value

9. BGP Considerations

This document defines the procedures and objects to create the BGP sessions and advertise the associated prefixes dynamically. Only the key information, for example, peer IP addresses, and peer AS numbers are exchanged via the PCEP protocol. Other parameters that are needed for the BGP session setup SHOULD be derived from their default values.

When the PCE sends out the PCInitiate message with the BPI object embedded to establish the BGP session between the PCC peers, the PCC SHOULD report the BGP session status. For instance, the PCC could respond with "BGP Session Establishment In Progress" initially and on session establishment send another PCRpt message with the state updated to "BGP Session Established". If there is any error during the BGP session establishment, the PCC SHOULD indicate the reason with the appropriate status value set in the BPI object.

Upon receiving such key information, the BGP module on the PCC SHOULD try to accomplish the task appointed by the PCEP protocol and report the successful status to the PCEP modules after the session is set up.

There is no influence on the current implementation of BGP Finite State Machine (FSM). The PCEP focuses only on the success and failure status of the BGP session and acts upon such information accordingly.

The error-handling procedures related to incorrect BGP parameters are specified in Section 6.1, Section 6.2, and Section 6.3.

10. Deployment Considerations

The information transferred in this document is mainly used for the BGP session setup, explicit route deployment and the prefix distribution. The planning, allocation and distribution of the peer addresses within IGP needs to be accomplished in advance and they are out of the scope of this document.

The communication of PCE and PCC described in this document MUST follow the state synchronization procedures described in [RFC8232], treat the three newly defined objects (BPI, EPR and PPA) associated with the same symbolic path name as the attribute of the same path in the LSP-DB (LSP State Database).

When PCE detects one or some of the PCCs are out of its control, it MUST recompute and redeploy the traffic engineering path for native IP on the currently active PCCs. The PCE MUST ensure the avoidance of the possible transient loop in such node failure when it deploys the explicit peer route on the PCCs.

In case of a PCE failure, a new PCE can gain control over the central controller instructions as described in [RFC9050].

As per the PCEP procedures in [RFC8281], the State Timeout Interval timer is used to ensure that a PCE failure does not result in automatic and immediate disruption for the services. Similarly, as per [RFC9050], the central controller instructions are not removed immediately upon PCE failure. Instead, they could be re-delegated to the new PCE before the expiration of this timer, or be cleaned up on the expiration of this timer. This allows for network clean up without manual intervention. The PCC supports the removal of CCI as one of the behaviors applied on the expiration of the State Timeout Interval timer.

11. Manageability Considerations

11.1. Control of Function and Policy

A PCE or PCC implementation SHOULD allow the PCECC Native-IP capability to be enabled/disabled as part of the global configuration.

11.2. Information and Data Models

[RFC7420] describes the PCEP MIB; this MIB could be extended to get the PCECC Native-IP capability status. The PCEP YANG [I-D.ietf-pce-pcep-yang] module could be extended to enable/disable the PCECC Native-IP capability.

11.3. Liveness Detection and Monitoring

Mechanisms defined in this document do not imply any new liveness detection and monitoring requirements in addition to those already listed in [RFC5440]. The operator relies on existing IP liveness detection and monitoring.

11.4. Verify Correct Operations

Verification of the mechanisms defined in this document can be built on those already listed in [RFC5440], [RFC8231] and [RFC9050]. Further, the operator needs to be able to verify the status of BGP sessions and prefix advertisements.

11.5. Requirements on Other Protocols

Mechanisms defined in this document require the interaction with BGP. Section 9 describes in detail the considerations regarding the BGP. During the BGP session establishment, the Local/Peer IP address MUST be dedicated to the usage of the native IP TE solution, and MUST NOT be used by other BGP sessions that are established manually or in other ways.

11.6. Impact on Network Operations

[RFC8821] describes the various deployment considerations in CCDR architecture and their impact on network operations.

12. Security Considerations

In this setup, the BGP sessions, prefix advertisement, and explicit peer route establishment are all controlled by the PCE. See [RFC4271] for security consideration of classical BGP implementation, and [RFC4272] for classical BGP vulnerabilities analysis. Security considerations in [RFC5440]for basic PCEP protocol, [RFC8231] for PCEP extension for stateful PCE and [RFC8281] for PCE-Initiated LSP setup SHOULD be considered. To prevent a bogus PCE from sending harmful messages to the network nodes, the network devices SHOULD authenticate the PCE and ensure a secure communication channel between them. Thus, the mechanisms described in [RFC8253] for the usage of TLS for PCEP and [RFC9050] for protection against malicious PCEs SHOULD be used.

If suitable default values as discussed in Section 9 aren't enough and securing the BGP transport is required(for example, the TCP-AO [RFC5925], it can be provided through the addition of optional TLVs to the BGP Peer Info object that conveys the necessary additional information (for example, a key chain [RFC8177]name).

13. IANA Considerations

13.1. Path Setup Type Registry

[RFC8408] created a registry within the "Path Computation Element Protocol (PCEP) Numbers" registry group called "PCEP Path Setup Types". IANA is requested to allocate a new code point within this registry, as follows:

Value          Description                        Reference
4              Native IP TE Path                  This document

13.2. PCECC-CAPABILITY sub-TLV's Flag field

Editorial Note (To be removed by RFC Editor): This experimental track document is allocating a code point in the registry under the standards action registry which is not allowed. [I-D.ietf-pce-iana-update] updates the registration policy to IETF review allowing for this allocation. Note that an early allocation was made when the document was being progressed in the standards track. At the time of publication, please remove this note and the reference to [I-D.ietf-pce-iana-update].

[RFC9050] created a registry within the "Path Computation Element Protocol (PCEP) Numbers" registry group to manage the value of the PCECC-CAPABILITY sub-TLV's 32-bit Flag field. IANA is requested to allocate a new bit position within this registry, as follows:

Bit       Name                   Reference
30        NATIVE IP              This document

13.3. PCEP Object

IANA is requested to allocate new codepoints in the "PCEP Objects" registry as follows:

Object-Class Value   Name                        Reference
44                   CCI Object                  This document
                     Object-Type
                       2: Native IP

46                BGP Peer Info                  This document
                     Object-Type
                       1: IPv4 address
                       2: IPv6 address

47                Explicit Peer Route            This document
                     Object-Type
                       1: IPv4 address
                       2: IPv6 address

48                Peer Prefix Advertisement      This document
                     Object-Type
                       1: IPv4 address
                       2: IPv6 address

13.4. PCEP-Error Object

IANA is requested to allocate new error types and error values within the "PCEP-ERROR Object Error Types and Values" registry of the "Path Computation Element Protocol (PCEP) Numbers" registry group for the following errors:

Error-Type  Meaning              Error-value
6      Mandatory Object missing
                                 19:Native IP object missing

10    Reception of an invalid object
                                 39:PCECC NATIVE-IP-TE-CAPABILITY bit
                                    is not set

19    Invalid Operation
                                 22:Only one BPI, EPR or PPA object can
                                    be included in this message
                                 29:Attempted Native-IP operations
                                    when the capability was not advertised
                                 30:Unknown Native-IP Info

33     Native IP TE failure
                           1:Local IP is in use
                           2:Remote IP is in use
                           3:Explicit Peer Route Error
                           4:EPR/BPI Peer Info mismatch
                           5:BPI/PPA Address Family mismatch
                           6:PPA/BPI Peer Info mismatch

The reference for the new Error-type/value should be set to this document.

13.5. CCI Object Flag Field

IANA is requested to create a new registry to manage the 16-bits Flag field of the new CCI Object called "CCI Object Flag Field for Native-IP". New values are to be assigned by IETF review [RFC8126]. Each bit should be tracked with the following qualities:

Currently, no flags are assigned.

13.6. BPI Object Status Code

IANA is requested to create a new registry "BPI Object Status Code Field" within the "Path Computation Element Protocol (PCEP) Numbers" registry group. New values are assigned by IETF review [RFC8126]. Each value should be tracked with the following qualities: value, meaning, and defining RFC. The following values are defined in this document:

Value           Meaning                                    Reference
    0           Reserved                                 This document
    1           BGP Session Established                  This document
    2           BGP Session Establishment In Progress    This document
    3           BGP Session Down                         This document
    4-255       Unassigned                               This document

13.7. BPI Object Error Code

IANA is requested to create a new registry "BPI Object Error Code Field" within the "Path Computation Element Protocol (PCEP) Numbers" registry group. New values are assigned by IETF review [RFC8126]. Each value should be tracked with the following qualities: value, meaning, and defining RFC. The following values are defined in this document:

Value     Meaning                                          Reference
    0     Reserved                                       This document
    1     ASes does not match, BGP Session Failure       This document
    2     Peer IP can't be reached, BGP Session Failure  This document
    3-255 Unassigned                                     This document

13.8. BPI Object Flag Field

IANA is requested to create a new registry "BPI Object Flag Field" within the "Path Computation Element Protocol (PCEP) Numbers" registry group. New values are to be assigned by IETF review [RFC8126]. Each bit should be tracked with the following qualities:

The following values are defined in this document:

Bit             Meaning                            Reference
0-6             Unassigned
7               T (IPnIP) bit                      This document

14. Contributor

Dhruv Dhody has contributed to this document.

15. Acknowledgement

Thanks Mike Koldychev, Susan Hares, Siva Sivabalan and Adam Simpson for their valuable suggestions and comments.

16. References

16.1. Normative References

[I-D.ietf-pce-iana-update]
Dhody, D. and A. Farrel, "Update to the IANA PCEP Registration Procedures and Allowing Experimental Error Codes", Work in Progress, Internet-Draft, draft-ietf-pce-iana-update-01, , <https://datatracker.ietf.org/doc/html/draft-ietf-pce-iana-update-01>.
[RFC2003]
Perkins, C., "IP Encapsulation within IP", RFC 2003, DOI 10.17487/RFC2003, , <https://www.rfc-editor.org/info/rfc2003>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC4271]
Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A Border Gateway Protocol 4 (BGP-4)", RFC 4271, DOI 10.17487/RFC4271, , <https://www.rfc-editor.org/info/rfc4271>.
[RFC5440]
Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation Element (PCE) Communication Protocol (PCEP)", RFC 5440, DOI 10.17487/RFC5440, , <https://www.rfc-editor.org/info/rfc5440>.
[RFC5511]
Farrel, A., "Routing Backus-Naur Form (RBNF): A Syntax Used to Form Encoding Rules in Various Routing Protocol Specifications", RFC 5511, DOI 10.17487/RFC5511, , <https://www.rfc-editor.org/info/rfc5511>.
[RFC5925]
Touch, J., Mankin, A., and R. Bonica, "The TCP Authentication Option", RFC 5925, DOI 10.17487/RFC5925, , <https://www.rfc-editor.org/info/rfc5925>.
[RFC7420]
Koushik, A., Stephan, E., Zhao, Q., King, D., and J. Hardwick, "Path Computation Element Communication Protocol (PCEP) Management Information Base (MIB) Module", RFC 7420, DOI 10.17487/RFC7420, , <https://www.rfc-editor.org/info/rfc7420>.
[RFC8126]
Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, , <https://www.rfc-editor.org/info/rfc8126>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC8231]
Crabbe, E., Minei, I., Medved, J., and R. Varga, "Path Computation Element Communication Protocol (PCEP) Extensions for Stateful PCE", RFC 8231, DOI 10.17487/RFC8231, , <https://www.rfc-editor.org/info/rfc8231>.
[RFC8232]
Crabbe, E., Minei, I., Medved, J., Varga, R., Zhang, X., and D. Dhody, "Optimizations of Label Switched Path State Synchronization Procedures for a Stateful PCE", RFC 8232, DOI 10.17487/RFC8232, , <https://www.rfc-editor.org/info/rfc8232>.
[RFC8253]
Lopez, D., Gonzalez de Dios, O., Wu, Q., and D. Dhody, "PCEPS: Usage of TLS to Provide a Secure Transport for the Path Computation Element Communication Protocol (PCEP)", RFC 8253, DOI 10.17487/RFC8253, , <https://www.rfc-editor.org/info/rfc8253>.
[RFC8281]
Crabbe, E., Minei, I., Sivabalan, S., and R. Varga, "Path Computation Element Communication Protocol (PCEP) Extensions for PCE-Initiated LSP Setup in a Stateful PCE Model", RFC 8281, DOI 10.17487/RFC8281, , <https://www.rfc-editor.org/info/rfc8281>.
[RFC8408]
Sivabalan, S., Tantsura, J., Minei, I., Varga, R., and J. Hardwick, "Conveying Path Setup Type in PCE Communication Protocol (PCEP) Messages", RFC 8408, DOI 10.17487/RFC8408, , <https://www.rfc-editor.org/info/rfc8408>.
[RFC9050]
Li, Z., Peng, S., Negi, M., Zhao, Q., and C. Zhou, "Path Computation Element Communication Protocol (PCEP) Procedures and Extensions for Using the PCE as a Central Controller (PCECC) of LSPs", RFC 9050, DOI 10.17487/RFC9050, , <https://www.rfc-editor.org/info/rfc9050>.

16.2. Informative References

[I-D.ietf-pce-pcep-yang]
Dhody, D., Beeram, V. P., Hardwick, J., and J. Tantsura, "A YANG Data Model for Path Computation Element Communications Protocol (PCEP)", Work in Progress, Internet-Draft, draft-ietf-pce-pcep-yang-25, , <https://datatracker.ietf.org/doc/html/draft-ietf-pce-pcep-yang-25>.
[RFC3209]
Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, , <https://www.rfc-editor.org/info/rfc3209>.
[RFC4272]
Murphy, S., "BGP Security Vulnerabilities Analysis", RFC 4272, DOI 10.17487/RFC4272, , <https://www.rfc-editor.org/info/rfc4272>.
[RFC5036]
Andersson, L., Ed., Minei, I., Ed., and B. Thomas, Ed., "LDP Specification", RFC 5036, DOI 10.17487/RFC5036, , <https://www.rfc-editor.org/info/rfc5036>.
[RFC7942]
Sheffer, Y. and A. Farrel, "Improving Awareness of Running Code: The Implementation Status Section", BCP 205, RFC 7942, DOI 10.17487/RFC7942, , <https://www.rfc-editor.org/info/rfc7942>.
[RFC8177]
Lindem, A., Ed., Qu, Y., Yeung, D., Chen, I., and J. Zhang, "YANG Data Model for Key Chains", RFC 8177, DOI 10.17487/RFC8177, , <https://www.rfc-editor.org/info/rfc8177>.
[RFC8283]
Farrel, A., Ed., Zhao, Q., Ed., Li, Z., and C. Zhou, "An Architecture for Use of PCE and the PCE Communication Protocol (PCEP) in a Network with Central Control", RFC 8283, DOI 10.17487/RFC8283, , <https://www.rfc-editor.org/info/rfc8283>.
[RFC8735]
Wang, A., Huang, X., Kou, C., Li, Z., and P. Mi, "Scenarios and Simulation Results of PCE in a Native IP Network", RFC 8735, DOI 10.17487/RFC8735, , <https://www.rfc-editor.org/info/rfc8735>.
[RFC8821]
Wang, A., Khasanov, B., Zhao, Q., and H. Chen, "PCE-Based Traffic Engineering (TE) in Native IP Networks", RFC 8821, DOI 10.17487/RFC8821, , <https://www.rfc-editor.org/info/rfc8821>.

Authors' Addresses

Aijun Wang
China Telecom
Beiqijia Town, Changping District
Beijing
Beijing, 102209
China
Boris Khasanov
MTS Web Services (MWS)
Andropova av.,18/9 115432
Moscow
Sheng Fang
Huawei Technologies
Huawei Bld., No.156 Beiqing Rd.
Beijing
China
Ren Tan
Huawei Technologies
Huawei Bld., No.156 Beiqing Rd.
Beijing
China
Chun Zhu
ZTE Corporation
50 Software Avenue, Yuhua District
Nanjing
Jiangsu, 210012
China