BESS Workgroup J. Rabadan, Ed. Internet-Draft S. Sathappan Intended status: Standards Track M. Gautam Expires: 26 December 2024 Nokia P. Brissette Cisco Systems W. Lin Juniper 24 June 2024 Domain Path (D-PATH) for Ethernet VPN (EVPN) Interconnect Networks draft-ietf-bess-evpn-dpath-01 Abstract The BGP Domain PATH (D-PATH) attribute is defined for Inter-Subnet Forwarding (ISF) BGP Sub-Address Families that advertise IP prefixes. When used along with EVPN IP Prefix routes or IP-VPN routes, it identifies the domain(s) through which the routes have passed and that information can be used by the receiver BGP speakers to detect routing loops or influence the BGP best path selection. This document extends the use of D-PATH so that it can also be used along with other EVPN route types. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 26 December 2024. Copyright Notice Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved. Rabadan, et al. Expires 26 December 2024 [Page 1] Internet-Draft D-PATH for Layer2 EVPN June 2024 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. D-PATH to Prevent Loops for EVPN Routes . . . . . . . . . 3 1.2. Add Path Visibility and Influence Best Path Selection for EVPN Routes . . . . . . . . . . . . . . . . . . . . . . . 4 2. Conventions used in this document . . . . . . . . . . . . . . 5 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Use of Domain Path Attribute (D-PATH) with EVPN routes . . . 6 4.1. D-PATH and Best Path Selection for MAC/IP Advertisement routes . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.2. D-PATH and Best Path Selection for Ethernet A-D per EVI routes . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.3. D-PATH and Best Path Selection for Inclusive Multicast Ethernet Tag routes . . . . . . . . . . . . . . . . . . . 10 4.4. Loop Detection . . . . . . . . . . . . . . . . . . . . . 10 4.5. Error Handling . . . . . . . . . . . . . . . . . . . . . 11 5. Use-Case Examples . . . . . . . . . . . . . . . . . . . . . . 11 6. Security Considerations . . . . . . . . . . . . . . . . . . . 13 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14 8. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 14 9. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 14 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 14 10.1. Normative References . . . . . . . . . . . . . . . . . . 14 10.2. Informative References . . . . . . . . . . . . . . . . . 15 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15 1. Introduction The BGP Domain PATH (D-PATH) attribute [I-D.ietf-bess-evpn-ipvpn-interworking] is defined for Inter-Subnet Forwarding (ISF) BGP Sub-Address Families that advertise IP prefixes. When used along with EVPN IP Prefix routes or IP-VPN routes, it identifies the domain(s) through which the routes have passed and that information can be used by the receiver BGP speakers to detect routing loops or influence the BGP best path selection. This document extends the use of D-PATH so that it can also be used along with other EVPN route types. Rabadan, et al. Expires 26 December 2024 [Page 2] Internet-Draft D-PATH for Layer2 EVPN June 2024 The D-PATH attribute can be used to prevent control plane loops for EVPN routes, or to provide full path visibility of all the EVPN Interconnect Gateways through which a route has gone and modify the best path selection based on it. Some use cases in which D-PATH can be used along with (non-IP Prefix) EVPN routes follow, but the use cases are not limited to the ones described in this section. 1.1. D-PATH to Prevent Loops for EVPN Routes Figure 1 illustrates an EVPN Interconnect case where EVPN MAC/IP Advertisement routes can be looped indefinitely. The three Gateways (GW1, GW2 and GW3) and PE1 in the diagram are attached to the same EVPN Broadcast Domain (BD1). However, BD1 is extended throughout three different domains that are interconnected by the Gateways, which follow [RFC9014] procedures. Suppose a host with MAC address M1 is learned on GW1 and GW1 advertises an EVPN MAC/IP Advertisement route for M1 into Domain-1 and Domain-2. When the route gets imported by GW2 and GW3 and later exported into Domain-3, GW2 and GW3 may redistribute each other's route for M1 back into Domain-1 and Domain-2, respectively, creating a loop. D-PATH can be used by the Gateways when redistributing the route between Domains, to identify the Domains through which the route for M1 has gone. When GW1 receives an EVPN MAC/IP Advertisement route for M1 that contains a D-PATH with a domain-id locally assigned, GW1 identifies the route as "looped". +----------------+ GW2 | EVPN +-------+ | Domain-1 | +---+ | | | |BD1| |---------------+ | | +---+ | | GW1 | +-------+ | PE1 +-------+ | | EVPN +-------+ | +---+ |---------------+ | Domain-3 | +---+ | | |BD1| | | | |BD1| | | +---+ |---------------+ | | +---+ | +---|---+ | GW3 | +---|---+ | | EVPN +-------+ | | M1--+ | Domain-2 | +---+ | | +--M2 | | |BD1| |---------------+ | | +---+ | | +-------+ +----------------+ Figure 1: Loops for EVPN routes Rabadan, et al. Expires 26 December 2024 [Page 3] Internet-Draft D-PATH for Layer2 EVPN June 2024 Similar examples are possible with EVPN VPWS services on the Gateways and PEs, where loop prevention for the redistributed A-D per EVI routes is needed. D-PATH provides the end to end path visibility that is required to prevent the loop. 1.2. Add Path Visibility and Influence Best Path Selection for EVPN Routes Figure 2 illustrates another [RFC9014] EVPN Interconnect case where, in addition to using D-PATH to prevent EVPN MAC/IP Advertisement route loops when redistributing routes between domains, the D-PATH attribute can also influence the best path selection for the routes. For example, if all the Gateways in the diagram are attached to the same BD1, an EVPN MAC/IP Advertisement route for MAC address M1 advertised by GW1 is advertised into Domain-1 and Domain-4. Two routes for M1 will arrive at GW3 with different route distinguishers and BGP Next Hops. If D-PATH is used by all the Gateways, the two routes arriving at GW3 will have a different sequence of domain-ids in the D-PATH attribute. GW3 can use the length of the D-PATH as a way of influencing the selection (i.e., the shortest D-PATH route is selected). D-PATH improves the path visibility of the route since it provides information about all the Domains through which the route has passed. +----------+ GW11 +----------+ GW2 +----------+ | EVPN +-------+ EVPN +-------+ EVPN | | Domain-1 | +---+ | Domain-2 | +---+ | Domain-3 | | | |BD1| | | |BD1| | | | | +---+ | | +---+ | | GW1 | +-------+ +-------+ | GW3 +-------+ | | | | +-------+ | +---+ |---------+ +----------+ +---------| +---+ | | |BD1| | | |BD1| | | +---+ |---------+ +----------------------------| +---+ | +---|---+ | GW12 | +---|---+ | | EVPN +-------+ EVPN | | M1--+ | Domain-4 | +---+ | Domain-5 | +--M2 | | |BD1| | | | | +---+ | | | +-------+ | +----------+ +-----------------------------+ Figure 2: Influence Best Path Selection for EVPN routes Rabadan, et al. Expires 26 December 2024 [Page 4] Internet-Draft D-PATH for Layer2 EVPN June 2024 2. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 3. Terminology This section summarizes the terminology that is used throughout the rest of the document. * AC: Attachment Circuit or logical interface associated to a given Broadcast Domain. To determine the AC on which a packet arrived, the PE examines the combination of a physical port and VLAN tags (where the VLAN tags can be individual c-tags, s-tags or ranges of both). * BD and BT: a Broadcast Domain and Bridge Table, as defined in [I-D.ietf-bess-rfc7432bis]. A BD is a group of PEs attached to the same EVPN layer-2 multipoint service. A BT is the instantiation of a Broadcast Domain in a PE. When there is a single Broadcast Domain in a given EVI, the MAC-VRF in each PE contains a single BT. When there are multiple BTs within the same MAC-VRF, each BT is associated to a different Ethernet Tag. The EVPN routes specific to a BT indicate which Ethernet Tag the route corresponds to. This document does not distinguish between a "Broadcast Domain" and a "Bridge Table", and will use the terms interchangeably (or will use the acronym "BD" to refer to either). Also, the way the BDs are grouped into MAC-VRFs depending on the service model (VLAN-based versus VLAN Bundle or VLAN-aware Bundle) is not relevant to the procedures specified in this document. * BUM: Broadcast, Unknown unicast and Multicast traffic. * ES and ESI: Ethernet Segment and Ethernet Segment Identifier, as defined in [I-D.ietf-bess-rfc7432bis]. * EVPN Domain: two PEs are in the same EVPN Domain if they are attached to the same service and the packets between them do not require a data path lookup of the inner frame (e.g., in the BD of a MAC-VRF) in any intermediate router. An EVPN Domain Gateway PE is always configured with multiple Domain identifiers (EVPN Domain-ID) in the MAC-VRF or VPWS that connects those EVPN Domains, each EVPN Domain-ID representing an EVPN Domain. Rabadan, et al. Expires 26 December 2024 [Page 5] Internet-Draft D-PATH for Layer2 EVPN June 2024 Example: Figure 3 illustrates an example where PE1 and PE2 belong to different EVPN Domains since packets between them (for flows between hosts with MAC addresses M1 and M2) require a MAC lookup in two of the gateways that are connecting the three EVPN Domains. E.g., if frames from M1 to M2 go through PE1, GW1, GW3 and PE2, a MAC lookup is performed at GW1 and GW3. GW1------------GW3 +------+ +------+ +-------------| BD1 | | BD1 |-------------+ PE1 +------+ +------+ PE2 +------+ | | +------+ M1-| BD1 | EVPN | EVPN | EVPN | BD1 |-M2 +------+ GW2 GW4 +---+--+ | +------+ +------+ | +-------------| BD1 | | BD1 |-------------+ +------+ +------+ +--------------+ EVPN Domain 1 EVPN Domain 2 EVPN Domain 3 <---------------> <------------> <----------------> Figure 3: EVPN Domain Interconnect Example * EVPN Domain Gateway: a PE where a service (BD or VPWS instance) is instantiated and is attached to two or more EVPN Domains. This document uses the term "EVPN Domain Gateway" or simply "Gateway". An example of EVPN Domain Gateway is a PE following the procedures in section 4.4 or section 4.6 of [RFC9014]. In the example in Figure 3, GW1 and GW2 connect EVPN Domains 1 and 2, whereas GW3 and GW4 connect EVPN Domains 2 and 3. GW1 and GW2 import the MAC/ IP Advertisement route for M1 coming from the EVPN Domain 1 into the MAC-VRF for BD1, and redistribute it into EVPN Domain 2. Likewise, GW3 and GW4 import the route into their MAC-VRF and re- advertise it into EVPN Domain 3. * MAC-VRF: a MAC Virtual Routing and Forwarding table, as defined in [I-D.ietf-bess-rfc7432bis]. It is also the instantiation of an EVI (EVPN Instance) in a PE. 4. Use of Domain Path Attribute (D-PATH) with EVPN routes This document extends the use of the D-PATH attribute specified in [I-D.ietf-bess-evpn-ipvpn-interworking] so that D-PATH can be advertised and processed along with the following EVPN route types: * EVPN MAC/IP Advertisement routes that are not used for Inter- Subnet Forwarding (ISF). Note that if the EVPN MAC/IP Advertisement route is used for Inter-Subnet Forwarding as in Rabadan, et al. Expires 26 December 2024 [Page 6] Internet-Draft D-PATH for Layer2 EVPN June 2024 [RFC9135], the procedures for the D-PATH advertisement and processing are described in [I-D.ietf-bess-evpn-ipvpn-interworking]. * EVPN A-D per EVI routes that are used for EVPN VPWS [RFC8214]. Advertised A-D per EVI routes not used for EVPN VPWS SHOULD NOT contain D-PATH. * EVPN Inclusive Multicast Ethernet Tag routes [I-D.ietf-bess-rfc7432bis]. As discussed, the use of D-PATH with EVPN IP Prefix routes is specified in [I-D.ietf-bess-evpn-ipvpn-interworking]. When used along with EVPN routes other than IP Prefix routes, the D-PATH attribute is characterized as follows: 1. D-PATH is composed of a sequence of Domain segments following the format specified in [I-D.ietf-bess-evpn-ipvpn-interworking] where each Domain is represented as . In this specification, DOMAIN-ID is an EVPN Domain identifier configured in an EVPN Domain Gateway and ISF_SAFI_TYPE is set to either 70 (EVPN) or 0 (local route). To simplify the explanation, this document represents the domains for EVPN routes as . 2. D-PATH identifies the sequence of EVPN Domains the route has gone through, with the last entry (rightmost) identifying the first PE or EVPN Domain Gateway that added the D-PATH attribute. 3. For non-Inter Subnet Forwarding EVPN MAC/IP Advertisement routes or EVPN A-D per EVI routes [I-D.ietf-bess-rfc7432bis], D-PATH SHOULD be added/modified by a EVPN Domain Gateway that redistributes the route between EVPN Domains and MAY be added by a PE or EVPN Domain Gateway that originates the route, as follows: a. An EVPN Domain Gateway that connects two EVPN Domains "X" and "Y", and receives a route on a EVPN Domain identified by a Domain-ID "X" SHOULD append a domain to the existing (or newly added) D-PATH attribute when redistributing the route to EVPN Domain "Y". The route is redistributed if it is first imported in a MAC-VRF (or VPWS instance), the MAC (or Ethernet Tag) is active, and policy allows the re-export of the route to a BGP neighbor. Rabadan, et al. Expires 26 December 2024 [Page 7] Internet-Draft D-PATH for Layer2 EVPN June 2024 b. An EVPN Domain Gateway MAY also add the D-PATH attribute for locally learned MACs or MAC/IP pairs. In this case, the domain added would be , where "A" is the Domain-ID configured on the Gateway's MAC-VRF that is specific to local routes (MAC/IP learned via local AC), and "0" is the TYPE of the EVPN Domain and indicates that the route is locally originated and not redistributed after receiving it from a BGP-EVPN neighbor. The EVPN Domain-ID for local routes MAY be shared by all the EVPN Domain Gateways of the same redundancy group for local routes, or each EVPN Domain Gateway of the redundancy group can use its own Domain-ID. c. A PE that is connected to a single EVPN Domain (therefore the PE is not an EVPN Domain Gateway) MAY add the D-PATH with a domain , where "B" is the Domain-ID configured on the PE's MAC-VRF (or VPWS) for locally learned MAC/IPs (or Ethernet Tag IDs for VPWS). "0" is the TYPE that indicates the route is not re-advertised, but originated in the PE. 4. For EVPN Inclusive Multicast Ethernet Tag routes, an EVPN Domain Gateway must not redistribute routes between Domains as specified in [RFC9014]. An EVPN Domain Gateway originates an EVPN Inclusive Multicast Ethernet Tag route per Domain to which the Gateway is attached, so that BUM traffic can be attracted from one Domain to the rest. Therefore, only the above point 3.b. applies to EVPN Domain Gateways. That is, an EVPN Domain Gateway MAY add a D-PATH attribute for the Inclusive Multicast Ethernet Tag routes generated for the EVPN Domains, where "A" is the configured local Domain-ID, and "0" is the TYPE that indicates the route is locally originated and not redistributed across EVPN Domains. When two or more EVPN Domain Gateways of the same redundancy group connect two EVPN Domains "X" and "Y" and D-PATH is used for EVPN Inclusive Multicast Ethernet Tag routes, it is RECOMMENDED to add the D-PATH attribute with the same local Domain-ID and only on "X" or "Y" but not on both Domains. In this case, all Gateways under the same redundancy group MUST choose the same Domain in which the D-PATH attribute is used. 5. On received EVPN routes, D-PATH is processed and used for loop detection (Section 4.4) as well as to influence the best path selection (Section 4.1, Section 4.2 and Section 4.3). 6. A Gateway PE SHOULD support the removal of the D-PATH attribute on import and on export, based on configuration. Rabadan, et al. Expires 26 December 2024 [Page 8] Internet-Draft D-PATH for Layer2 EVPN June 2024 4.1. D-PATH and Best Path Selection for MAC/IP Advertisement routes When two (or more) MAC/IP Advertisement routes with the same route key (and same or different RDs) are received, a best path selection algorithm is used to select and install only one route. The best path selection for MAC/IP Advertisement routes is specified in [I-D.ietf-bess-rfc7432bis], in section 7.13.1, and this document modifies the algorithm by including the D-PATH comparison across EVPN MAC/IP Advertisement routes after tie-breaking rule 5 in [I-D.ietf-bess-rfc7432bis] section 7.13.1, which removes from consideration routes that are not tied for higher degree of preference. If none of the tie-breaking rules up to (and including) rule 5 produces a single route, the router compares the D-PATH attribute in the remaining candidate routes: 1. The routes with the shortest D-PATH are preferred, hence routes not tied for the shortest D-PATH are removed. Routes without D-PATH are considered zero-length D-PATH. 2. Then routes with the numerically lowest left-most Domain-ID are preferred (only the Domain-ID is compared, and not the ISF_SAFI_TYPE). Hence, routes not tied for the numerically lowest left-most Domain-ID are removed from consideration. When comparing two Domain-IDs, the two six byte values are compared starting with the Global Admin field. The lowest value in the first differing byte between the two six byte values, is considered to belong to the "numerically lowest Domain-ID". If the steps above do not produce a single route, then the rest of the rules in [I-D.ietf-bess-rfc7432bis] follow. 4.2. D-PATH and Best Path Selection for Ethernet A-D per EVI routes When two (or more) EVPN A-D per EVI routes with the same route key (and same or different RDs) are received for a Virtual Private Wire Service (VPWS), a best path selection algorithm is used. The best path selection for EVPN A-D per EVI routes is specified in [I-D.ietf-bess-rfc7432bis], in section 7.13.2, and this document modifies the algorithm by including the D-PATH comparison across EVPN A-D per EVI routes in the same way Section 4.1 does it for EVPN MAC/ IP Advertisement routes. That is, rules 1 and 2 of Section 4.1 are interleaved between rules 5 and 6 of [I-D.ietf-bess-rfc7432bis]. Rabadan, et al. Expires 26 December 2024 [Page 9] Internet-Draft D-PATH for Layer2 EVPN June 2024 4.3. D-PATH and Best Path Selection for Inclusive Multicast Ethernet Tag routes When two (or more) EVPN Inclusive Multicast Ethernet Tag routes with the same route key (and same or different RDs) are received for a MAC-VRF, a best path selection algorithm is used and only one of them is programmed. The selection algorithm follows [I-D.ietf-bess-rfc7432bis] the same D-PATH comparison steps as in Section 4.1 interleaved between rules 5 and 6 of [I-D.ietf-bess-rfc7432bis]. 4.4. Loop Detection An EVPN route received by a PE with a D-PATH attribute that contains one or more of its locally associated Domain-IDs for the MAC-VRF or VPWS instance is considered to be a looped route. A looped route MUST NOT be redistributed to a different domain and SHOULD be flagged as "looped". EVPN Inclusive Multicast Ethernet Tag looped routes MUST NOT be installed, where "install" in this document means "create forwarding state". An EVPN MAC/IP Advertisement looped route or an A-D per EVI looped route (in EVPN VPWS services) MAY be installed if selected as the best route. For instance, in the example of Figure 3, assuming PE1 advertises M1's MAC/IP and does not add the D-PATH attribute, the EVPN Domain Gateway GW1 receives two MAC/IP Advertisement routes for M1's MAC/IP: * A MAC/IP Advertisement route with next hop PE1 and no D-PATH. * A MAC/IP Advertisement route with next hop GW2 and D-PATH={length=1,<6500:1:EVPN>}, assuming that the Domain-ID for EVPN Domain 1 is 6500:1. In this case, EVPN Domain Gateway GW1 flags the MAC/IP Advertisement route with D-PATH as "looped", and does not install the MAC in the BD, and does not redistribute the route back to EVPN Domain 1 (since the route includes one of GW1's Domain-IDs). In case the MAC/IP Advertisement route with next hop PE1 is withdrawn, GW1 may install the route with next hop GW2 and D-PATH <6500:1:EVPN>; this may help speed up convergence in case of failures. The procedures described in this section, based on D-PATH, can be used along with the Ethernet Segment Identifier of the received routes as a way to detect looped routes on EVPN domain gateways attached to an Interconnect Ethernet Segment as in [RFC9014]. An EVPN domain gateway MUST NOT redistribute a received EVPN MAC/IP Rabadan, et al. Expires 26 December 2024 [Page 10] Internet-Draft D-PATH for Layer2 EVPN June 2024 route or EVPN A-D per EVI route with an Ethernet Segment Identifier value that matches the value of a local Ethernet Segment, irrespective of the D-PATH Domain-IDs. 4.5. Error Handling The error handling for the D-PATH attribute is described in [I-D.ietf-bess-evpn-ipvpn-interworking]. This document extends the use of D-PATH to non-Inter Subnet Forwarding (non-ISF) EVPN routes. 5. Use-Case Examples This section illustrates the use of D-PATH in EVPN routes with examples. Figure 4 and Figure 5 illustrate an integrated interconnect solution for an EVPN BD, as described in section 4.4 and section 4.6 of [RFC9014]. GW1 and GW2 are EVPN Domain Gateways connecting two EVPN Domains identified by D-PATH domain {1:1:EVPN} and {1:2:EVPN}, respectively. Received Ethernet A-D routes, ES routes, and Inclusive Multicast routes from the routers in one EVPN Domain are consumed and processed by GW1 and GW2, but not redistributed to the other EVPN Domain. However, MAC/IP Advertisement routes received by GW1 and GW2 in one EVPN Domain are processed and, if installed, redistributed into the other EVPN Domain. +----EVPN Domain-1---+ +----EVPN Domain-2--+ | 1:1:EVPN | GW1 | 1:2:EVPN | | +---------+ | | | +-----+ | | | | | BD1 | X <-+ | PE1 | +-----+ | | PE2 +---------+ +---------+ | +---------+ | +-----+ | | | | | +-----+ | M1-----| BD1 | | | | | | | BD1 |-----M2 | +-----+ | -------> | | | | +-----+ | +---------+ (RT2)M1/IP1 | | | +---------+ | +---------+ | | | | +-----+ | |(RT2)M1/IP1 | | | | BD1 | | --+ <1:1:EVPN> | | | +-----+ | | | +---------+ | | | GW2 | | +---------------------+ +-------------------+ Figure 4: EVPN Interconnect Rabadan, et al. Expires 26 December 2024 [Page 11] Internet-Draft D-PATH for Layer2 EVPN June 2024 Consider the example of Figure 4, where PE1 advertises a MAC/IP Advertisement route for M1/IP1. The route is processed and installed by GW1 and GW2 in BD1, and both redistribute the routes into the EVPN Domain-2. By using D-PATH in GW1 and GW2, when the route is received on PE2, PE2 has the visibility of the EVPN Domains through which the route has gone, and can also use the D-PATH for best path selection. In addition, GW1 and GW2 can compare the D-PATH of the incoming routes with their local list of EVPN Domain-IDs, and detect looped routes if any of the local EVPN Domain-IDs matches a domain in the received D-PATH. This procedure prevents the redistribution of the route back into EVPN Domain-1. For example, when GW1 receives the MAC/IP Advertisement route for M1/IP1 with D-PATH <1:1:EVPN>, GW1 identifies the route as looped and it does not redistribute it back to Domain-1. The M1/IP1 route with Next Hop PE1 is installed. If M1/IP1 with Next Hop PE1 is withdrawn, GW1 MAY install the route M1/ IP1 with Next Hop GW2, as specified in Section 4.4. The example of Figure 5 illustrates how GW1 and GW2 can also have local ACs in BD1 and learn local MAC (or MAC/IP) addresses from devices connected to the ACs. +----EVPN Domain-1---+ +----EVPN Domain-2--+ | 1:1:EVPN | GW1 | 1:2:EVPN | | +---------+ | | | +-----+ | | | +-->X| | BD1 | |X<--+ | PE1 | | +-----+ | | PE2 +---------+ | +---------+ | +---------+ | +-----+ | | | | | | +-----+ | M1-----| BD1 | | | | | +---> | | BD1 |-----M2 | +-----+ | | | | | | +-----+ | +---------+ | | | | +---------+ | | | GW2 | | | | <---+-- +---------+ (RT2)M3/IP3 | | (RT2)M3/IP3 | +-----+ | {1:3:0} | | {1:3:0} | | BD1 | | | | | | +-----+ | ---+ | | +----|----+ | | | | | | +---------------------+ | +-------------------+ + M3 Figure 5: EVPN Interconnect local AC Assuming GW2 learns M3/IP3 via local AC, GW2 advertises a MAC/IP Advertisement route for M3/IP3 into each of the EVPN Domains that GW2 is connected to. As described in Section 4, GW2 can advertise these Rabadan, et al. Expires 26 December 2024 [Page 12] Internet-Draft D-PATH for Layer2 EVPN June 2024 two MAC/IP Advertisement routes with a configured EVPN Domain-ID for local MAC/IPs routes that can be shared with GW1. Consider this EVPN Domain-ID is 1:3 and it is configured on both, GW1 and GW2. When GW2 advertises the route into each EVPN Domain, it adds the D-PATH attribute with a domain {1:3:0}. These routes are flagged by GW1 as "looped" since 1:3 is configured as a local EVPN Domain-ID in GW1. In addition, PE1 and PE2 receive the routes with the D-PATH and they have the visibility of the origin of the routes, in this case local EVPN Domain Gateway routes. This information can be used to influence the best path selection in case of multiple routes for M3/ IP3 are received on PE1 or PE2 for BD1. As an alternative solution to configuring the same EVPN Domain-ID for local routes on both EVPN Domain Gateways, GW2 can be configured with EVPN Domain-ID 1:3 for local routes, and GW1 can use a different EVPN Domain-ID, e.g., 1:4. In this case, GW2 advertises the route for M3/ IP3 into each EVPN Domain as before, but now GW1 does not flag the route as "looped" since 1:3 is not on the list of GW1's local EVPN Domain-IDs. GW1 receives the routes from both EVPN Domains, and GW1 selects the route from e.g., EVPN Domain-1. GW1 then installs the route in its BD and redistributes the route into EVPN Domain-2 with D-PATH {1:1:EVPN, 1:3:0}. When PE2 receives two routes for M3/IP3, one from GW2 with D-PATH {1:3:0} and another from GW1 with D-PATH {1:1:EVPN, 1:3:0}, PE2 uses best path selection and choose to send its traffic to GW2. Also GW2 receives the route for M3/IP3 from GW1 and mark it as "looped" since that route conveys its own EVPN Domain- IDs 1:1 and 1:3. In a nutshell, the use of D-PATH in MAC/IP Advertisement routes helps prevent loops and influences the best path selection so that PEs choose the shortest paths to the destination PEs. 6. Security Considerations Most of the considerations included in [I-D.ietf-bess-evpn-ipvpn-interworking] related to D-PATH apply to this document. In particular, a correct use of the D-PATH will prevent control plane and data plane loops in the network, however an incorrect configuration of the DOMAIN-IDs or an inconsistent support of D-PATH on the Gateway PEs may lead to the detection of false route loops, dropping packets or may result in inconsistent and sub-optimal forwarding. As an additional security mechanism, a PE following this specification that receives an EVPN route from a non-upgraded PE should discard the route via policy if the route contains the D-PATH attribute. Rabadan, et al. Expires 26 December 2024 [Page 13] Internet-Draft D-PATH for Layer2 EVPN June 2024 7. IANA Considerations None. 8. Acknowledgments The authors would like to thank Jeff Haas for his thorough review of this document. 9. Contributors In addition to the authors included on the front page, the following people contributed significantly: Vinod Prabhu, Nokia Bin Wen, Comcast 10. References 10.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [I-D.ietf-bess-evpn-ipvpn-interworking] Rabadan, J., Sajassi, A., Rosen, E., Drake, J., Lin, W., Uttaro, J., and A. Simpson, "EVPN Interworking with IPVPN", Work in Progress, Internet-Draft, draft-ietf-bess- evpn-ipvpn-interworking-11, 24 June 2024, . [I-D.ietf-bess-rfc7432bis] Sajassi, A., Burdet, L. A., Drake, J., and J. Rabadan, "BGP MPLS-Based Ethernet VPN", Work in Progress, Internet- Draft, draft-ietf-bess-rfc7432bis-09, 2 May 2024, . Rabadan, et al. Expires 26 December 2024 [Page 14] Internet-Draft D-PATH for Layer2 EVPN June 2024 [RFC9014] Rabadan, J., Ed., Sathappan, S., Henderickx, W., Sajassi, A., and J. Drake, "Interconnect Solution for Ethernet VPN (EVPN) Overlay Networks", RFC 9014, DOI 10.17487/RFC9014, May 2021, . [RFC8214] Boutros, S., Sajassi, A., Salam, S., Drake, J., and J. Rabadan, "Virtual Private Wire Service Support in Ethernet VPN", RFC 8214, DOI 10.17487/RFC8214, August 2017, . 10.2. Informative References [RFC9135] Sajassi, A., Salam, S., Thoria, S., Drake, J., and J. Rabadan, "Integrated Routing and Bridging in Ethernet VPN (EVPN)", RFC 9135, DOI 10.17487/RFC9135, October 2021, . Authors' Addresses J. Rabadan (editor) Nokia 520 Almanor Avenue Sunnyvale, CA 94085 United States of America Email: jorge.rabadan@nokia.com S. Sathappan Nokia 520 Almanor Avenue Sunnyvale, CA 94085 United States of America Email: senthil.sathappan@nokia.com M. Gautam Nokia 520 Almanor Avenue Sunnyvale, CA 94085 United States of America Email: mallika.gautam@nokia.com P. Brissette Cisco Systems Canada Email: pbrisset@cisco.com Rabadan, et al. Expires 26 December 2024 [Page 15] Internet-Draft D-PATH for Layer2 EVPN June 2024 W. Lin Juniper United States of America Email: wlin@juniper.net Rabadan, et al. Expires 26 December 2024 [Page 16]